ER500 1535nm 500µJ Eye-Safe Laser for Long-Range LiDAR and Rangefinders

Datasheet revision: Rev. A / 2026-10-27. Read the revision note (PDF) — corrected values and document-control status. To get the test record for a specific unit, request the test conditions.

PRODUCT OVERVIEW

ER500 is a compact 1535 nm pulsed laser source based on Er:Yb glass microchip technology, designed for long-range LiDAR and rangefinders.

Pulse energy

≥500 µJ

Repetition rate

1~10Hz

Pulse width

6 ns

Dimensions

35×8×6.8 mm³

Weight

12 g

KEY FEATURES

• ✔ 1535 nm Eye-Safe Operation (Class 1)
• ✔ 500µJ Pulse Energy
• ✔ Compact OEM Design
• ✔ High Pulse Stability
• ✔ Long Lifetime

Optical Specifications

Mechanical, Electrical and Environmental Specifications

Integration Considerations

Review package constraints, electrical requirements and thermal conditions before integration. The driver supply must be matched to the specified voltage and current, and the drive pulse width must remain within the stated limit. For application-specific questions, contact our engineering team with your system requirements.

APPLICATIONS

DOWNLOADS

• Datasheet (PDF)
• 3D model (GLB) — open in any 3D viewer or CAD tool
• Outline drawing (STEP) — request from our team
• Integration guide — request from our team

Product Description

ER500 1.54µm / 1535nm 500µJ Eye-Safe Erbium Glass Microchip DPSS Laser

The ER500 is a high-energy 1535nm eye-safe erbium glass microchip DPSS laser designed as a transmitter core for long-range LiDAR, laser rangefinders and target-designation modules. It combines a diode-pumped Er³⁺:glass gain medium with a compact microchip cavity, delivering nanosecond pulses in a slim board-level package that is easy to integrate into airborne, vehicle and handheld systems.

The laser provides single-pulse energy of at least 500µJ with a typical pulse width of 6ns and a pulse repetition rate adjustable from 1 to 10Hz. Pulse stability is specified at 10%. The raw beam diameter is about 0.3mm, with divergence ≤ 7mrad and TEM₀₀ beam mode, giving a tight, near-Gaussian beam that is straightforward to collimate for multi-kilometer outdoor ranging.

Mechanically, the ER500 is housed in a 35×8×6.8mm³ package and weighs around 12g, making it suitable for direct mounting on driver PCBs where space and mass are at a premium. It is driven from a low-voltage, high-current pulse: typical load voltage is about 2V, operating current is 20A, drive pulse width ≤ 2.4ms and repetition rate up to 10Hz. The driver power supply must match these parameters; if not, the laser may fail to start properly or could be overloaded and permanently damaged.

The ER500 is designed for harsh environmental conditions. The operating temperature range is −40°C to +65°C and the storage range is −55°C to +75°C. Shock resistance is rated at 1500G for 0.5ms, and vibration tolerance is 20–2000Hz at 20G. Lifetime is specified at more than 1 million shots, aligning with the requirements of long-life fielded LiDAR and rangefinding platforms.

Operation guidelines emphasize safe wiring and correct parameter setup. Power must be fully disconnected before making connections; polarity must be checked carefully, and all terminals must be firmly tightened to avoid short circuits, reverse polarity and intermittent contacts. After wiring, parameters on the driver should be set strictly according to the factory test report before enabling emission, ensuring that voltage, current, pulse width and repetition rate stay within the specified range. The output window must be kept clean and should not be touched; if contamination occurs, it should be cleaned before operation. When mounting the device via the side lugs, a torque of about 0.2 N·m is recommended to maintain mechanical stability without distorting the housing.

With its 1.54µm wavelength, the ER500 operates in an eye-safer band where radiation is strongly absorbed by the cornea and lens instead of directly reaching the retina. This, combined with low atmospheric attenuation and good penetration in haze, rain and aerosol, makes the ER500 especially suitable for open, man-in-the-loop applications. Typical scenarios include long-range laser rangefinders, UAV and airborne LiDAR payloads, compact EO/IR gimbals, ship-borne and vehicle-mounted sensor heads, as well as industrial mapping, structural monitoring and robotic perception systems that require multi-kilometer performance with an eye-safe source.

OUTLINE DIMENSION

Figure 1 Outline Dimensions(mm)

Operating Instructions

• Match the laser driver to the ER500 laser.
  The laser driver power supply must be properly matched to the laser.
  The typical load voltage of the ER500is < 2 V, with an operating current of 20 A, pulse width < 2 ms, and a repetition rate of 10 Hz. For the exact operating parameters, please refer to the attached factory test report. The laser driver power supply must meet these requirements; otherwise, the laser may fail to operate properly or could be overloaded and permanently damaged. Therefore, before wiring, carefully check the laser specification sheet and confirm that the laser is compatible with the selected driver.
• Always disconnect power before wiring.
  Before making any connections, make sure the power is switched off and completely isolated. During wiring, carefully check the positive and negative terminals of the laser and ensure correct polarity. After the wiring is completed, perform a thorough inspection to confirm that all connections are correct, in order to avoid short circuits, reverse polarity, and other faults. At the same time, make sure all terminals are firmly secured to prevent poor contact due to loose wiring.
• Set operating parameters according to the factory test report.
  After confirming that the wiring is correct, set the corresponding parameters on the driver according to the attached factory test report. Once the parameters are correctly set, turn on the driver; the laser should then operate normally.
• Keep the laser output window clean.
  Take care to keep the laser output window clean and do not touch the window surface. If contamination occurs, clean the window thoroughly beforeoperating the laser.
• Use the correct mounting torque.
  Because the overall length of the laser housing is relatively long, when fastening the laser via the mounting lugs on both sides, use a torque screwdriver set to 2 N·m. Excessive or insufficient torque may affect the mechanical stability and performance of the laser.

Mounting, Interface and OEM / ODM

Mounting and thermal path. The outline drawing above gives the package envelope. Mounting features and the recommended thermal interface are confirmed against the drawing for your build; send the host-side footprint if you need a matched heatsink or bracket.

Trigger and electrical interface. The source is driven by an external driver. Trigger input, harness, connector and timing are defined with the driver and host system, within the drive-pulse width and repetition-rate limits in the table above. Share your interface requirements and we will confirm them for ER500.

OEM / ODM. Package, optical configuration and electrical interface can be reviewed for project-specific programmes, subject to technical feasibility. Scope and review process.

Request a Quote · Ask an Engineer · Request STEP / 2D drawing

Product FAQ

• Is this an eye-safe source?
  Class 1 eye-safe at the specified 1535 nm wavelength.
• What is the typical use?
  Rangefinding, LiDAR, sensing and OEM instrument integration.
• Can the package be customised?
  See OEM / ODM for the customisation scope and review process.